0800 088 6248 Get a guide price
  1. Home
  2. Guides
  3. What are the parts of a shopfront called?

What are the parts of a shopfront called?

A traditional shopfront has a fascia for the name, a cornice above it, pilasters at each side, a stallriser below the glass, and a glazed display divided by mullions and transoms. Modern frontages may drop some of these, but the same lines still set the proportions. Knowing the names makes drawings, quotes and planning conversations far easier.

Written by the Shopfront Specialists team. Checked November 2026.

Restored period shopfront with a painted timber fascia, console brackets and a tiled entrance lobby

What are the main parts of a shopfront?

The main parts are the fascia, cornice, pilasters, console brackets, stallriser, cill, mullions, transoms, door and threshold. Together they form a frame around the glass, in much the same way that a picture frame holds and sets off a painting.

That frame comes from classical architecture, where columns carry a beam and the beam carries a roof line. A shopfront is a small domestic version of the same idea: pilasters stand for columns, the fascia and cornice stand for the beam, and the stallriser gives the whole thing a base. Once you see it that way, it is obvious why a front with no stallriser and an oversized fascia feels top-heavy.

PartWhat it isWhat to check
CorniceProjecting ledge above the fasciaWeathering on top, so rain runs off
FasciaBand carrying the nameDepth against the height of the front
Console bracketScrolled end to the fasciaRot behind it, loose fixings
PilasterFlat column at each sideDamp at the foot
MullionVertical dividerLine with the windows above
TransomHorizontal dividerLine with the door head
StallriserSolid base under the glassHeight, impact damage
CillLedge under the glassFall outward, drainage
RevealSide face of a recessDepth, and what fixes to it
ThresholdFloor line at the doorUpstand height, level

What sits above the glass on a shopfront?

The fascia, the cornice and often a blind box sit above the glass, with console brackets closing each end of the fascia. Your name goes on the fascia, and it is usually the first thing to get out of proportion, as modern ceilings and old shutter boxes push it downward.

A cornice looks decorative but does real work. It throws rainwater clear of the fascia, and a good one has a lead or metal weathering on top with a slight fall away from the wall. Skip that weathering and water sits on the joinery, which is why so many old fascias rot from the top down.

Consoles, sometimes called corbels, stop the fascia from simply running out at each end. They also mark the boundary between one shop and its neighbour. If you have surviving consoles, keep them, as a fascia ending against a good bracket looks finished in a way a plain board never does. A blind box is a slim housing above the glass for a retractable awning, and older fronts often have a redundant one hidden behind later boarding.

What are pilasters for?

Pilasters mark the edges of the shop and visually carry the fascia down to the ground. They are usually flat columns applied to the brick piers, with a plinth at the bottom and a capital or console at the top.

Their job is mainly to tie the shopfront into the building. Where a pilaster sits directly below a pier on the upper floors, the eye reads a load path from roof to pavement, and the elevation feels solid. A frontage with glass running to the party wall and nothing marking the edge tends to look as if the upper floors are hovering.

On the practical side, the foot of a timber pilaster is one of the first places to fail. Water splashes off the pavement, the end grain drinks it in and the rot climbs inside while the paint stays looking fine. Press the bottom 150mm with a thumb when you survey an old front.

What is a stallriser and how high should it be?

A stallriser is the solid panel under the display window, and it typically stands around 450mm to 600mm high. The name comes from the market stall board it replaced, and its practical job is to keep glass away from boots, trolleys, splash and road grit.

Height is a design decision as much as a practical one. Too low and the shop loses its base, while too high and a fashion or food display drops out of view. Wall glazing up to 800mm counts as a critical location in Wales, Scotland and Northern Ireland, and England's diagram uses the same 800mm mark, so a stallriser can also simplify the glass.

Materials range from panelled timber to glazed tile, stone, render and metal cladding. Timber needs a proper plinth and ventilation behind it, because damp from the ground wall rots it from the back. Glazed tile is hard-wearing and wipes clean, which explains why butchers and dairies used it for so long.

What is the difference between mullions, transoms and glazing bars?

A mullion is a vertical divider, a transom is a horizontal one, and a glazing bar is a thinner member that divides a single pane. Mullions usually carry load or stiffen the frame, while glazing bars exist mainly for proportion.

The panel above a transom is called a toplight or fanlight, and it was once used for ventilation or lettering. Keep that transom in line with the door head and the whole front gains a calm horizontal datum. Letting the door head and transom sit at different heights, even by 40mm, is the kind of mistake you can't stop seeing once you have noticed it.

What are a recessed lobby, reveal and threshold?

A recessed lobby is a door set back from the glass line, the reveal is the side face of that recess, and the threshold is where the floor crosses the door line. Recesses give shelter, extra display length and a place for the door to swing without crossing the pavement.

The soffit, or ceiling of the recess, is easy to forget and very visible at night. Old lobbies often keep a mosaic floor with the name of an earlier trader set into it. These are worth lifting a mat to look for, and worth protecting if you find one. Thresholds decide how level the entrance is, so check the fall of the floor before anything else is drawn.

Common questions

Is it stallriser or stall riser?

Both are used, and the one-word form is common in planning guides. The trade term is also shortened to riser, so don't be surprised to see that on a drawing.

What is a bressummer?

A bressummer is the heavy beam spanning the shop opening and carrying the wall above. It may be timber on old buildings or steel on later ones, and it is the first thing to check when the old fascia comes off.

What is a sightline?

A sightline is the visible face width of a frame member, as you see it from the front. Designers talk about it because slim sightlines mean more glass, and a 10mm difference is noticeable across a whole frontage.

What is the difference between a fascia and a frieze?

In classical architecture the frieze is the band between the architrave and the cornice, and a shop fascia occupies that position. On shopfronts the two terms are often used for the same board, and fascia is the one you will see on drawings and quotes.

Related pages

Tell us about your frontage

Send the address and a photo. We'll come and measure it, at no cost.

Call usGet a guide price